Call (844) 430-7681
Los Angeles County · a neighborhood of the City of Los Angeles

Electrician in Studio City

Licensed electricians for Studio City, from the canyon streets off Laurel Canyon and Fryman Road to the flats around Colfax Meadows, with an on-site visit and a written price.

Call (844) 430-7681Request a free estimate

What you can call us for in Studio City

Small repairs welcome · Free estimates on eligible work · Licensed C-10 #1100231Call (844) 430-7681

Studio City is two neighborhoods split by Ventura Boulevard. North of it are the flats: tracts like Laurel Terrace and Agnes Avenue, built in the late 1920s and 1930s for people working at the studio lot that is now Radford Studio Center, then post-war houses and courtyard apartments on the last of the farmland. South of it the ground rises into the Santa Monica Mountains, and the canyon streets are almost all single-family homes.

Those hills are on the Fire Department's list of communities in the city's Very High Fire Hazard Severity Zone. For electrical work that means questions about outdoor equipment and wiring extended down a slope over decades, alongside the remodels, chargers and panel replacements found everywhere else. Every price is in writing, after we've seen the job.

What we do in Studio City

Everything we do in Studio City, with what each job usually involves here. The photos are from our own jobs.

Service upgrade in progress: new meter main and conduit
Service upgrade in progress: new meter main and conduit

Panel upgrades in Studio City

Service upgrades for remodeled Colfax Meadows houses and replacements for original panels in the hills, including the mast and weatherhead on old overhead drops.

More on panel upgradesCall (844) 430-7681

Tesla Wall Connector, garage install
Tesla Wall Connector, garage install

EV charger installation in Studio City

Chargers in hillside garages, on steep driveways with weather-rated equipment, and in assigned condo parking off Ventura Boulevard.

More on EV charger installationCall (844) 430-7681

Inside a new main panel: breakers, neutral and ground bars, every conductor labeled and dressed
Inside a new main panel: breakers, neutral and ground bars, every conductor labeled and dressed

Rewiring in Studio City

Rewiring studio-era houses in Laurel Terrace and the flats, and replacing wiring extended down a slope one addition at a time.

More on rewiringCall (844) 430-7681

Four-unit meter stack for a multi-family building
Four-unit meter stack for a multi-family building

Commercial electrical in Studio City

Dedicated circuits, lighting retrofits and tenant improvements for the restaurants, shops and offices along Ventura Boulevard and in Tujunga Village, scheduled around their hours.

More on commercial electricalCall (844) 430-7681

Also: subpanels, dedicated circuits, 240-volt outlets for dryers and ranges, exterior and security lighting, hard-wired smoke alarms, and small repairs of every kind.

Need an electrician in Studio City? Call now, or send the form and we'll call you back to set a time for an on-site estimate.

Call (844) 430-7681Request an estimate
Studio City at a glance
ZIP codes
91604, part of 91602
Jurisdiction
A neighborhood of the City of Los Angeles, Los Angeles County

Areas we cover in Studio City

  • Colfax Meadows
  • Laurel Terrace
  • Fryman Canyon area
  • Laurel Canyon hillsides
  • Tujunga Village
  • Radford Studio Center area
  • Ventura Boulevard corridor

Good to know

  • Inside the City of Los Angeles: LADBS and LADWP
  • Hillsides south of Ventura Boulevard are in the city's fire zone
  • Studio-era tracts from the late 1920s and 30s in the flats
  • Courtyard apartments and condos along the main streets

4.9★ from 232 Google reviews across our service area · Licensed C-10 #1100231 · Free estimates on eligible work

What's common in Studio City homes

Studio City has two housing stocks separated by Ventura Boulevard, and the electrical work is different on each side.

  • Hillside homes south of the Boulevard. Houses off Laurel Canyon, Fryman Road and the canyon streets, with sub-panels added for pool houses and additions, outdoor lighting on long runs, and gate and pump circuits. We trace the whole system before adding to it.
  • Colfax Meadows and the flats. Tree-lined streets between Moorpark, Colfax, Tujunga and the river, where houses have been enlarged or rebuilt outright. Service upgrades sized for a new kitchen and a second air-conditioning system are routine.
  • Laurel Terrace, Agnes Avenue and the other studio-era tracts. Late-1920s and 1930s houses with early wiring and small services, on streets the city's survey has flagged as potential historic districts. Rewiring here is planned to respect the house.
  • Courtyard apartments and condos. 1940s courtyard buildings on Tujunga Avenue and the later apartments and condos, with shared meter banks, HOA approvals and chargers in assigned parking.

Permits and power in Studio City

Studio City (ZIP codes 91604, part of 91602) is City of Los Angeles; Burbank, a couple of miles east past Toluca Lake, has its own utility and rules, but nothing on this side of the line does. In the hills south of Ventura Boulevard, the Fire Department requires brush cleared up to 200 feet from any structure and lists plants that may not stand close to a house. That doesn't change an electrical permit for work inside, but it shapes how we route and mount landscape lighting, gate circuits and anything on an exterior wall.

The canyon streets also have old overhead service drops: long spans to the house and weatherheads that haven't been touched in decades. On a panel replacement there, we check the mast and weatherhead on the site visit, so if they need work it's in the written price, not a surprise on the day.

Permits come from the Los Angeles Department of Building and Safety (LADBS). A new circuit, an EV charger, a sub-panel or a panel replacement is permitted work, and LADBS will not send an inspector until the permit is issued. We pull it under our license and meet the inspector at the end.

Power comes from the Los Angeles Department of Water and Power (LADWP), not Southern California Edison. For repairs, lighting, new outlets and a charger that fits on the existing panel, LADWP is not involved. For a panel or service upgrade it is: the job starts with LADWP's free meter spot, where an Electric Service Representative visits within five to fifteen business days, confirms where the new equipment may go and leaves a sketch at the job (single-family services up to 320 amps can be requested online). When only the meter needs setting, LADWP says that generally happens within ten working days. If the existing LADWP service can carry the new load there are generally no LADWP charges; work in the street, on a transformer or on the lines can add cost and time, and we find that out before you commit.

The permits and utilities guide explains the whole picture for the three counties we serve.

Around Studio City

Sherman Oaks, Valley Village, North Hollywood, Toluca Lake and Encino are City of Los Angeles neighborhoods with LADBS permits and LADWP power, and so is Hollywood on the far side of the Cahuenga Pass. Burbank, beyond Toluca Lake, is an independent city with its own Building Division and its own utility, Burbank Water and Power.

See the full list of areas we cover across Los Angeles, Orange and Ventura counties.

From our jobs

Panel upgrade with a new LADWP meter, labeled circuits and solar disconnect labeling
Panel upgrade with a new LADWP meter, labeled circuits and solar disconnect labeling
Tesla Wall Connector, exterior wall install
Tesla Wall Connector, exterior wall install
Recessed and niche lighting in a new-build living room
Recessed and niche lighting in a new-build living room
Original Zinsco panel with a rusted cover and hand-written labels
Original Zinsco panel with a rusted cover and hand-written labels

See more recent work

Simple from the first call

How a job runs.

No phone quotes and no guessing. A written estimate after we've seen the job, then permitted, inspected work.

STEP 01

Reach out

Call or send the form. A photo of the panel or the problem helps us come prepared.

STEP 02

On-site visit

We come to your home or business and look at the panel, wiring or site.

STEP 03

Written estimate

Scope, price and timeline in writing before you decide anything.

STEP 04

Permitted, inspected work

We pull the permit, coordinate your utility when needed, and finish with the inspection.

Questions people ask

Is my Studio City house in the Very High Fire Hazard Severity Zone?

If it's in the hills south of Ventura Boulevard, very likely. The Fire Department lists Studio City among the communities in the zone, and its online Fire Zone Map gives the answer for a specific address. Being in the zone means brush clearance up to 200 feet from the house and limits on what grows near it; it doesn't change the permit for electrical work inside, but it does shape how we route and mount anything outdoors.

We're remodeling a house in Colfax Meadows. When should the electrical be sized?

Before the plans are final. A new kitchen, a second air-conditioning system and a few more bathrooms can double the load on a 1940s service, and LADWP's side of a service upgrade is the longest step in the project. We do the load calculation early, settle the service size with your contractor or designer, and line up the rough-in and final inspections with the rest of the job.

My hillside house has three sub-panels and nobody knows what feeds what. Can you sort it out?

Yes, and it's a common request south of the Boulevard. We trace every feeder from the main service through each sub-panel, label the circuits, check the grounding and bonding, and tell you plainly what you have. That's also when we can tell you whether the service can carry a charger or a pool heater, or whether an upgrade comes first.

Can a charger go on a steep driveway where the car doesn't reach the garage?

Usually, yes. The charger is mounted on an exterior wall or a post with weather-rated equipment, and the circuit runs in conduit from the panel. On hillside lots the distance and the voltage drop over a long run decide the wire size, and the site visit is where we measure it and put the price in writing.

Ready when you are.

Call now, or send the form and we'll call you back to schedule an on-site estimate.

Call (844) 430-7681Request a free estimate
Call (844) 430-7681Free estimate